|
 |
 |
|
 |
The Extron MTP R 15HD A Mini Twisted Pair Receiver and MTP RL 15HD A Mini Twisted Pair Receiver with Loop Through work with the MTP T 15HD A Transmitter to transmit RGB, component, S-video, or composite video and summed mono audio (L+R) signals long distances over a single unshielded twisted pair (UTP) cable. The MTP 15HD A Series can be used with any CAT 5, 5e, or 6 twisted pair cable or with Extron Enhanced Skew-Free™ A/V UTP cable (patent pending) for cable runs of up to 600 feet (185 meters) with XGA signals or up to 450 feet (135 meters) with UXGA signals.
Extron MTP 15HD A transmitters and receivers precisely optimize image quality for various UTP cable lengths using adjustment controls on both the transmitter and receiver. The transmitters feature a pre-peaking switch that provides additional compensation at the front end for the longest cable runs. The receivers offer continuously variable gain and peaking controls, allowing users to dial in the exact amount of gain and peaking required for each unique cable run.
The Extron MTP R 15HD A Mini Twisted Pair Receiver accepts video and audio signals on a female RJ-45 connector. Video signals are output on a female 15-pin HD connector while up to two identical balanced or unbalanced mono audio signals are output on a 3.5 mm captive screw connector. The MTP R 15HD A receiver features separate continuously variable level and peaking adjustments that enable users to compensate for any signal degradation associated with long cable runs. A set of dip switches on the rear panel make it easy to configure the output signal and output sync formats.
The Extron MTP RL 15HD A Mini Twisted Pair Receiver with Loop Through has all of the same features and functionality as the MTP R 15HD A, with an added female RJ-45 output connector. This additional buffered output enables multiple MTP RL 15HD A receivers to be connected in series, reducing the number of parallel cable runs required.
The MTP 15HD A Series transmitter and receivers are compatible with resolutions up to 1600 x 1200 (UXGA) and are ideal for such applications as large training facilities, museums, airports, movie theaters, and hotels. These products are ideal for systems where high resolution video signals must be transmitted long distances to a display, or where space is limited in conduit, or for audio/video systems where cabling might be exposed or visible.
When using data grade twisted pair cable for sending high-resolution video signals long distances, a problem called skew can cause a distortion in the image, resulting in visible color separation. Extron offers two options for solving this problem and restoring image quality. The first option is to place an SEQ 100 15HD Skew Equalizer at the receiving end of any cable run where skew is a problem. The second option is to use Extron's Enhanced Skew-Free™ A/V UTP cable to make system connections.
Because the MTP 15HD A Series transmitter and receivers utilize UTP cable for the distribution of high resolution RGBHV and audio signals over long distances, they offer considerable advantages in cost, performance, and ease of installation. UTP cable is a fraction of the size of coaxial cable, and much lighter, more flexible, and less expensive, thus providing A/V system designers and installers with an economical, space efficient solution for a variety of applications.
Extron MTP Transmitters and Receivers are part of the VersaTools® family of economical, compact products designed for easy integration into new and existing A/V environments. MTPs are compact so they can fit just about anywhere: in equipment racks, under tables and desktops, or next to a projector.
- Receives high resolution computer-video and summed mono audio (L+R) signals over a single CAT 5, 5e, or 6 UTP cable
- Compatible with RGBHV, RGBs, RGsB, RsGsBs, component video, S-video, and composite video
- HDTV component video compatible (bi-level or tri-level sync)
- Continuously variable level and peaking (sharpness) controls
- Additional buffered UTP output (MTP RL 15HD A only)
- LED power indicator on front panel
- Compact 1U, quarter rack width, rugged metal enclosure
- External international power supply included (part number 70-055-01)
| MTP 15HD A Series |
|
| Video — all models |
| Number/signal type |
1 set of proprietary analog signals |
| Connectors |
1 female RJ-45 |
|
| Video input and loop through — MTP T 15HD A transmitter |
| Number/signal type |
1 analog RGBHV, RGBS, RGsB (selectable), component video; or
1 S-video and 1 composite video; or
3 composite video
1 buffered RGBHV, RGBS, RGsB local monitor loop through |
| Connectors |
2 female 15-pin HD |
| Nominal level |
1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB
0.3 Vp-p for R-Y and B-Y of component video, and for C of S-video |
| Minimum/maximum levels |
0.3 V to 1.45 Vp-p |
| Impedance |
75 ohms |
| Horizontal frequency |
15 kHz to 130 kHz |
| Vertical frequency |
30 Hz to 150 Hz |
| Return loss |
<-30 dB @ 5 MHz |
| DC offset (max. allowable) |
250 mV |
|
| Video output — MTP R 15HD A, MTP RL 15HD A receivers |
| Number/signal type |
1 set of proprietary analog signals (MTP RL 15HD A only)
1 analog RGBHV, RGBS, RGsB (selectable), component video; or
1 S-video and 1 composite video; or
3 composite video |
| Connectors |
1 female RJ‑45 (MTP RL 15HD A only)
1 female 15-pin HD |
| Nominal level |
1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB
0.3 Vp-p for R-Y and B-Y of component video, and for C of S-video |
| Minimum/maximum levels |
0.3 V to 1.45 Vp-p |
| Impedance |
75 ohms |
| Return loss |
<-30 dB @ 5 MHz |
| DC offset |
<±20 mV with input at 0 offset |
|
| Sync |
| Output type |
RGBHV, RGBS, RGsB |
| Standards |
NTSC 3.58, NTSC 4.43, PAL, SECAM |
| Input level (transmitter) |
3.5 V to 5.5 Vp-p, unterminated |
| Output level (receivers) |
4.0 V to 5.0 Vp-p, unterminated |
| Input impedance (transmitter) |
510 ohms |
| Output impedance (receivers) |
110 ohms |
| Max. input voltage (transmitter) |
5.5 Vp-p |
| Polarity |
|
| Transmitter |
Positive or negative (follows input polarity) |
| Receivers |
Positive or negative (switch-selectable) |
|
| Audio — all models |
| Number/signal type |
1 set of proprietary analog signals |
| Connectors |
1 female RJ-45 |
| Gain |
±0.75 dB |
| Frequency response |
20 Hz to 20 kHz, ±1 dB |
| THD + Noise |
0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level |
| S/N |
>70 dB at maximum output (unweighted) |
| CMRR |
>43 dB @ 20 Hz to 20 kHz |
|
| Audio input — MTP T 15HD A transmitter |
| Number/signal type |
1 stereo, unbalanced |
| Connectors |
(1) 3.5 mm mini stereo jack |
| Impedance |
>10k ohms, unbalanced |
| Nominal level |
+4 dBu (1.23 Vrms), -10 dBV (316 mVrms) |
| Maximum level |
+18dBu, (unbalanced) at 1%THD+N |
| NOTE |
|
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu | |
|
| Audio output — MTP R 15HD A, MTP RL 15HD A receivers |
| Number/signal type |
2 mono, balanced/unbalanced |
| Connectors |
(1) 3.5 mm captive screw connector, 5 pole |
| Impedance |
50 ohms unbalanced, 100 ohms balanced |
| Nominal level |
+4 dBu (1.23 Vrms), -10 dBV (316 mVrms) |
|
| General |
| Power |
Supplied by an external power supply |
| External power supply |
100 VAC to 240 VAC, 50/60 Hz, external, autoswitchable; to 12 VDC, 1 A, regulated |
| Power input requirements |
12 VDC, 500 mA |
| Temperature/humidity |
Storage -40° to +158°F (-40° to +70°C) / 10% to 90%, noncondensing
Operating +32° to +122°F (0° to +50°C) / 10% to 90%, noncondensing |
| Rack mount |
Yes, with optional 1U rack shelf, part #60-190-01 or 60-604-01; or VersaTools® rack shelf, part #60-190-20 or 60-604-20
Also furniture mountable with optional Mini Under-Desk Mounting Kit, part #70‑212‑01; or projector mountable with optional projector mounting kit, part #70‑217‑01 or 70-077-04 |
| Enclosure type |
Metal |
| Enclosure dimensions |
1.7" H x 4.3" W x 3.0" D (1U high, quarter rack wide)
4.3 cm H x 10.9 cm W x 7.6 cm D
(Depth excludes connectors.) |
| Product weight |
0.4 lbs (0.2 kg) |
| Shipping weight |
2 lbs (1 kg) |
| Vibration |
ISTA 1A in carton (International Safe Transit Association) |
| Listings |
UL, CUL |
| Compliances |
CE, FCC Class A, VCCI, AS/NZS, ICES |
| MTBF |
30,000 hours |
|
|
 |
 |
|
|
|
|
|
|
|
|
)
