|
 |
 |
|
 |
The Extron SW MTP 15HD A Series is a versatile family of switchers for selecting and transmitting high resolution computer-video and audio signals to presentation displays over a single unshielded twisted pair cable (UTP cable). The SW2 MTP T 15HD A, SW4 MTP T 15HD A, and SW6 MTP T 15HD A are two, four and six input, one output switchers that transmit RGBHV, RGBS, RGsB, HDTV, and other high resolution video and audio signals to a compatible MTP R 15HD A receiver. The SW MTP 15HD A series of switchers can be used with Extron Enhanced Skew-Free A/V UTP cable (patent pending) or any CAT 5, 5e, or 6 data grade twisted pair cable for point-to-point cable runs of up to 600 feet (185 meters) with XGA signals, and 450 feet (135 meters) with UXGA signals.
Each model accepts two, four, or six computer video and audio inputs on female 15-pin HD connectors and 3.5 mm stereo audio jacks. The switcher transmits the selected computer video and summed mono (L+R) audio signal to a compatible twisted pair receiver. Also, the switcher features a second audio output from a 3.5 mm captive screw connector for sending a balanced or unbalanced line level stereo audio signal to a local amplifier, recording device, or video conferencing codec.
Each switcher can be controlled using the front panel or remotely via contact closure or RS-232 signals. The dual-function remote control feature allows for numerous installation and control options. For example, the switcher can be installed in a secure location, such as an equipment rack or cabinet, and the control of the switcher can be managed using the optional Extron IR 102 Universal Remote Control Kit, or Extron KP 6 Keypad Remote Control, or Extron IP Link control interface to create cost-effective solutions with maximum functionality.
Using the autoswitching feature, the switcher can be set to switch automatically to the active source. For example, a number of wall plate receptacles can be installed around a room, each routed to a different input of the switcher. When an active computer-video source is connected to the wall plate, the switcher automatically selects that input. When two or more sources are detected at the same time the highest numbered input is automatically selected. The autoswitch function can be enabled or disabled via front panel buttons.
Part of the VersaTools family of economical, compact products, the SW MTP 15HD A Series of switchers are designed for easy integration into new and existing A/V environments. The entire family of Extron MTP 15HD products sets the price/performance standard for audio/video twisted pair technology. The MTP 15HD Series is a complete twisted pair system including transmitters, receivers, and switchers, providing the ability to send, route, and distribute high resolution video, audio, and control signals. The SW MTP Series is ideal for systems where high resolution video signals must be transmitted long distances to a display, or where space is limited in conduit, or for audio/video systems which cabling might be exposed or visible.
Inputs — Two, four, and six input models available
Outputs — Transmits a computer video and summed mono audio signal (L+R) to an MTP R 15HD A mini twisted pair receiver on a female RJ-45 output connector. A captive screw connector is also provided for balanced or unbalanced stereo audio output.
Autoswitching — Input sources are selected automatically when the switcher detects an active sync signal, making the SW MTP T switchers ideal for automatic routing and unattended operation.
RS-232 control — Rear panel, RS-232 port enables control via PC-based control software. Extron's Simple Instruction Set (SIS™) allows for quick and easy programming.
KP 6 Keypad Remote Control — The optional Extron KP 6 is a keypad remote control for switching the inputs on the SW MTP T Series. The KP 6 comes with a 25-foot (8 meters) cable to connect the switcher's 9-pin remote control port to the KP 6.
IR control — With the optional IR 102 Remote Control Kit, the SW MTP T switchers can be easily controlled with an IR 102 handheld remote.
Compact metal enclosure — 1U, half rack width metal enclosure
Versatile mounting options — Rack, under-desk, and projector-mountable
Power indicator — Front panel LED for easy troubleshooting
Power supply — External international power supply included
| Video |
| Number/signal type |
1 set of proprietary analog signals |
| Connectors |
1 female RJ‑45 |
|
| Video input |
| Number/signal type |
2, 4, or 6 (depending on the model) analog VGA-UXGA RGBHV, RGBS, RGsB, component video, S-Video or composite video |
| Connectors |
2, 4, or 6 (depending on the model) female 15-pin HD |
| Nominal level |
1 Vp-p for Y of component video and S-video, and for composite video
0.7V p-p for RGB
0.3V p-p for R-Y and B-Y of component video, and for C of S-video |
| Minimum/maximum levels |
Analog: 0.3 V to 1 Vp-p with no offset |
| Impedance |
75 ohms |
| Horizontal frequency |
15 kHz to 130 kHz |
| Vertical frequency |
30 Hz to 150 Hz |
| Return loss |
<-30 dB @ 5 MHz |
| DC offset (max. allowable) |
2 V |
|
| Video output — refer to twisted pair receivers' specifications and manuals |
|
| Sync |
| Input type |
RGBHV, RGBS, RGsB |
| Standards |
NTSC 3.58, NTSC 4.43, PAL, SECAM |
| Input level |
2.5 V to 5.5 V |
| Input impedance |
560 ohms |
| Max input voltage |
5.5 V |
|
| Audio |
| Number/signal type |
1 set of proprietary analog signals |
| Connectors |
1 female RJ‑45 |
| Gain |
±0.75 dB |
| Frequency response |
20 Hz to 20 kHz, ±1 dB |
| THD + Noise |
0.01% @ 1 kHz, 0.03% @ 20 kHz |
| S/N |
>100 dB at maximum output, unweighted |
| Crosstalk |
<-70 dB,@ 20 Hz to 20 kHz, +4 dBu stereo output |
| Stereo channel separation |
>65 dB @ 20 Hz to 20 kHz |
| CMRR |
>43 dB @ 20 Hz to 20 kHz |
|
| Audio input |
| Number/signal type |
2, 4, or 6 (depending on the model) stereo, unbalanced |
| Connectors |
2, 4, or 6 (depending on the model) 3.5 mm mini audio jacks (tip, ring, sleeve) |
| Impedance |
>10k ohms unbalanced |
| Nominal level |
-10 dBV (316 mVrms) |
| Maximum level |
+16 dBV, unbalanced, at <1% THD+N |
| NOTE |
|
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu | |
|
| Audio output |
| Number/signal type |
1 set of proprietary analog signals to be sent to an MTP receiver
1 stereo, balanced/unbalanced |
| Connectors |
1 female RJ‑45 (for proprietary signals)
(1) 3.5 mm captive screw connector, 5 pole |
| Impedance |
50 ohms unbalanced, 100 ohms balanced (for the stereo output) |
| Gain error |
±1 dB channel to channel (for stereo output) |
| Maximum level (Hi-Z) |
>+23 dBu, balanced, at <1% THD+N (for stereo output) |
| Maximum level (600 ohm) |
>+17 dBu, balanced at <1% THD+N (for stereo output) |
| Stereo channel separation |
>60 dB @ 1 kHz |
|
| Control/remote — switcher/transmitter |
| Serial control port |
RS-232, 9-pin female D connector (shared with contact closure) |
| Baud rate and protocol |
9600 baud, 8 data bits, 1 stop bit, no parity |
| Serial control pin configurations |
2 = TX, 3 = RX, 5 = GND |
| Contact closure |
RS-232, 9-pin female D connector (shared with serial control) |
| Contact closure pin configurations |
1 = input 1, 4 = input 2, 5 = GND, 6 = input 3, 7 = input 4, 8 = input 5, 9 = input 6 |
| Program control |
Extron's control/configuration program for Windows®
Extron's Simple Instruction Set (SIS™) |
|
| General |
| Power |
| Supplied by |
an external power supply |
|
| NOTE |
|
The SW MTP Series transmitters cannot supply remote power to or receive remote power from attached receivers. | |
| External power supply |
100 VAC to 240 VAC, 50/60 Hz, external, autoswitchable; to 12 VDC, 1 A, regulated |
| Power input requirements |
12 VDC, 0.6 A |
| Temperature/humidity |
Storage -40° to +158°F (-40° to +70°C) / 10% to 90%, noncondensing
Operating +32° to +122°F (0° to +50°C) / 10% to 90%, noncondensing |
| Rack mount |
Yes, with optional 1U rack shelf, part #60-190-01 or 60-604-01; or VersaTools® rack shelf, part #60-190-20 or 60-604-20
Also furniture mountable with optional Under-Desk Mounting Kit #70-212-01 |
| Enclosure type |
Metal |
| Enclosure dimensions |
1.75" H x 8.75" W x 3.0" D (1U high, half rack wide)
4.4 cm H x 22.2 cm W x 7.6 cm D
(Depth excludes connectors and toggle switch.) |
| Product weight |
0.8 lbs (0.4 kg) |
| Shipping weight |
3 lbs (2 kg) |
| Vibration |
ISTA 1A in carton (International Safe Transit Association) |
| Listings |
UL, CUL |
| Compliances |
CE, FCC Class A, VCCI, AS/NZS, ICES |
| MTBF |
30,000 hours |
|
|
 |
 |
|
|
|
|
|
|
|
|
)
